Wii u controller mods mod#
Wii u controller mods pro#
Wii u controller mods mods#
Wii u controller mods plus#

This was because I only wanted the original button colours. I used 4 pin 5v LED strips (One 5v line, 3 Gnd lines for RGB). Take your time.ДЄnother great thing is that the Gamecube controllers also have a 5v line, which is uncommon now with wireless controllers. The best tip I can give is to constantly test the LEDs, (I used an Arduino to test them) and test that the buttons contact pads are properly working. It's best to solder before gluing in place. Just try to place the LEDs as low as possible, and if you can't, you can shave a bit on the tape down with a set of small files. Issue is, they aren't the easiest to put in without the button contact pads getting in the way. Luckily, Gamecube controllers can have LED's modded in every button except Z and Start. Then you can either buy replacement stickboxes (which I've heard are bad) or source them from other Nintendo products from around that era (Gamecube, Wii etc.). Luckily, the controller I had was good, but if not, you will need to de-solder the potentiometers, and if your stickbox is metal, de-solder that too (some are metal soldered in, some are plastic screwed in). If the analog stick feels excessively loose, then you might need to repair them. The main thing that you might have to repair is the stickboxes. The sticks and buttons were completely replaced. I don't do huge washes, but I used a few glasses/screen cleaners to remove the dirt (these contain rubbing alcohol, so you can use that instead). This one that I got from my friend was very dirty, both internally and externally. Gamecube controllers aren't made often anymore, so they tend to get dirty quickly. Now compress the triggers, and pull them out. Moving to the back side of the casing, you can take the four screws off, and then the two covers. Then you can take out the PCB (make sure the rumble motor doesn't fall out). Then all you have to do is pull up from the bottom half, and it should come right off.

Wii u controller mods pro#

Isn't very common, you might have to buy a new screwdriver or kit, I personally use the ifixit precision screwdriver set, that came in the pro tech toolkit, but other screwdriver sets will work too.ДЇirst you want to take the 6 tri-wing screws off the back of the controller.I used glasses cleaners, since I had those lying around.Rubbing alcohol of some kind (somewhat optional) I believe that it is one of 8 cores in networking wire. The thinner wire measures about 0.85mm thick, and was given to me. I used a mix of 24 gauge stranded wire, and some even thinner solid core wire.RGB 5v LEDs Make sure that they are the 4 pin version, where there is a common 5v, and 3 Grounds for the RGB control I bought something similar to this (I bought completely clear ones).

Wii u controller mods plus#

Plenty are on Ebay in many different colours, plus they're actually decent quality (excluding the Z button, which is molded incorrectly).

All colours can be found here (or you can wait for deals when a new listing is made)

Best place to buy them would be on Ebay, or a local second hand store.

The regular colours of Gamecube controllers will all have the Nintendo Gamecube logo in the center of the controller, and will have the logos behind the C-Stick and D-Pad on the back of the controller too.

Make sure to get an official one, most third party controllers aren't that good.

Wii u controller mods mod#

You can decide how easy or hard your mod can be.

Wii u controller mods mods#

While my controller may be cool, it's better if it suits what you like, which is why I have a list of other mods that I've seen, so you can customize your controller even further.

I also suggest to try to make your controller different. I highly suggest reading though it, and checking the images for extra info. I'll walk you through how I made this custom controller, and suggest some extra mods to do at the end. Not to mention too, it's really easy to get it working on PC. tournament and there's bound to be people with their modded controllers.

Luckily for us, the Gamecube controller is one of the most modded, and supported controllers out there, look in any Super Smash Bros. Custom buttons, sticks, and LEDs, sure why not.

None of which are really unique to each person, so what are you to do? Mod it. Gamecube controllers are my favorite types of controllers, but in North America, the three most common colours of them are Platinum, Black and Indigo colours. Have you ever had a game controller that you really loved, but wasn't personalized for you? Well that's how I felt with my Gamecube controller.